JM プロジェクトは、主に Linux 関連のマニュアルページの日本語ページを翻訳・公開しています。
... ロセス全ての優先度を指定した値に設定する。 Traditionally, only a privileged process could lower the nice value (i.e., set a higher priority). However, since Linux 2.6.12, an unprivileged process can decrease the nice value of a target process that has a ... 。 上記のものに加えて setpriority () では以下のエラーがある: EACCES The caller attempted to set a lower nice value (i.e., a higher process priority), but did not have the required privilege (on Linux: did not have the CAP_SYS_NICE capability). EPERM プロ ... ... ロセス全ての優先度を指定した値に設定する。 Traditionally, only a privileged process could lower the nice value (i.e., set a higher priority). However, since Linux 2.6.12, an unprivileged process can decrease the nice value of a target process that has a ... 。 上記のものに加えて setpriority () では以下のエラーがある: EACCES The caller attempted to set a lower nice value (i.e., a higher process priority), but did not have the required privilege (on Linux: did not have the CAP_SYS_NICE capability). EPERM プロ ... ... 利用可能なので、使用すべきではない。 Prior to Linux 5.5 iopl () allowed the thread to disable interrupts while running at a higher I/O privilege level. This will probably crash the system, and is not recommended. Prior to Linux 3.7, on some architecture ... ... x 2.4.21/2.6; obsolete since Linux 4.14) If enabled, the TCP stack makes decisions that prefer lower latency as opposed to higher throughput. It this option is disabled, then higher throughput is preferred. An example of an application where this defau ... maximum number of times initial SYNs for an active TCP connection attempt will be retransmitted. This value should not be higher than 255. The default value is 6, which corresponds to retrying for up to approximately 127 seconds. Before Linux 3.7, the ... ... bytes. When inserting the hole inside file, the contents of the file starting at offset will be shifted upward (i.e., to a higher file offset) by len bytes. Inserting a hole inside a file increases the file size by len bytes. This mode has the same lim ... ... git groups to left of radix character */ char *grouping; /* Each element is the number of digits in a group; elements with higher indices are further left. An element with value CHAR_MAX means that no further grouping is done. An element with value 0 m ... ... k into two chunks of a smaller order (thus with half the size) or combine two contiguous chunks into one larger chunk of a higher order (thus with double the size) to satisfy allocation requests and to counter memory fragmentation. The order matches th ... r 0) available and has 3 chunks of 4 megabytes (order 10) available. If the memory is heavily fragmented, the counters for higher order chunks will be zero and allocation of large contiguous areas will fail. Further information about the zones can be f ... ... k into two chunks of a smaller order (thus with half the size) or combine two contiguous chunks into one larger chunk of a higher order (thus with double the size) to satisfy allocation requests and to counter memory fragmentation. The order matches th ... r 0) available and has 3 chunks of 4 megabytes (order 10) available. If the memory is heavily fragmented, the counters for higher order chunks will be zero and allocation of large contiguous areas will fail. Further information about the zones can be f ... ... e console. (For a discussion of log levels, see syslog (2).) By default, console_loglevel is set to log messages at levels higher than KERN_DEBUG . This boot argument will cause the kernel to also print messages logged at level KERN_DEBUG . The console ... ... olete. In glibc 2.25 and later, defining _REENTRANT is equivalent to defining _POSIX_C_SOURCE with the value 199606L. If a higher POSIX conformance level is selected by any other means (such as _POSIX_C_SOURCE itself, _XOPEN_SOURCE , _DEFAULT_SOURCE , ... 日本語の文書やマニュアルを配布している個人/プロジェクトへのリンクです。